Vertex Standard FT-1000MP - Manual (Page 110)

Page 108 O
PERATING
M
ANUAL
Menu Selection and Settings
Menu Selection Setting Table
Func No. Function Setting Range Default
0-1 Memory Group 1 Channels 1 ~ 99 01 ~ 99
0-2 Memory Group 2 Channels 0 ~ 99 OFF
0-3 Memory Group 3 Channels 0 ~ 99 OFF
0-4 Memory Group 4 Channels 0 ~ 99 OFF
0-5 Memory Group 5 Channels 0 ~ 99 OFF
0-6 Quick Memory Channel Banks 1 ~ 5 5
0-7 – – –
0-8 [A u B] Auto Channel Up ON/OFF OFF
0-9 EDSP ON/OFF ON
1-0 VFO-A & VFO-B Dial Speed 2/4 4
1-1 Shuttle Jog Dial Speed 1 mS ~ 100 mS 50 mS
1-2 IF SHIFT/WIDTH Step Size 10/20 Hz 10 Hz
1-3 Main VFO-A Tuning Step Size 0.62(5)/1.25/2.50/5.00/10.00/20.00 Hz 10.00 Hz
1-4 SUB VFO-B Tuning Step Size 0.62(5)/1.25/2.50/5.00/10.00/20.00 Hz 10.00 Hz
1-5 Channel Step Size 1 ~ 100 kHz 10 kHz
1-6 Quick Split Offset (±) 1 ~ 100 kHz 5 kHz
1-7 Automatic Selection of the ON/OFF OFF
AGC Decay Time
1-8 CLAR M-Tune Function ON/OFF ON
1-9 CLAR Tuning Step Size 0.62(5)/1.25/2.50/5.00/10.00/20.00 Hz 10.00 Hz
2-0 Scan Pause ON/OFF ON
2-1 Scan Resume Mode CAR STOP/CAR TIME/CAR SLOW CAR STOP
2-2 – – –
2-3 Memory Scan Speed (Dwell Time) 100 mS ~ 1000 mS (1S) 200 mS
2-4 VFO Scan Speed (Dwell Time) 1 mS ~ 100 mS 10 mS
2-5 Auto Memory Write OFF/GROUP x/ GROUPS ALL OFF
2-6 Memory Scan Skip OFF/OFF OFF
2-7 Scan Delay Time 1 S ~ 10 S 5 S
2-8 Noise Blanker A1 ~ A15 & B1 ~ B15 A12
2-9 NOTCH Mode IF NOTCH/AUTO DSP/SELECT IF NOTCH
3-0 Frequency Display OFFSET/CARRIER OFFSET
3-1 Display Resolution 10 Hz/100 Hz/1000 Hz (1 kHz) 10 Hz
3-2 ETS (Enchanced Tuning Scale) CLAR/DIAL CLAR
3-3 Transverter Frequency Display OFF/50/144/430 OFF
3-4 Dimmer (Display Brightness) LOW/HI HI
3-5 Panel Display Mode CLAR/CH FREQ/OFFSET/CW PITCH CLAR
3-6 SUB VFO-B S-Meter ON/OFF ON
3-7 MAIN VFO-A Meter Peak-Hold OFF/10 mS ~ 2000 mS (2S) OFF
3-8 SUB VFO-B Meter Peak-Hold OFF/10 mS ~ 2000 mS (2S) OFF
3-9 – – –
4-0 RF Output Power (Limit) Hi (100 W) / Lo-2 (25W) / Lo-1(10 W) Hi (100 W)
4-1 Key & Panel Beeper ON/OFF ON