Hotpoint Ariston Aqualtis AQS73D 29 EU-A - Manuale (Pagina 9)

EN
9 9
Wash cycles and options
Wash options
Super Wash
This option offers a high-
performance wash due to the
greater quantity of water used in
the initial phase of the cycle, and
due to the increased wash cycle
duration, is particularly useful for
the removal of stubborn stains.
It can be used with or without
bleach. If you desire bleaching,
insert the extra tray compartment
(3) into compartment 1. When
pouring in the bleach, be careful
not to exceed the “max” level
marked on the central pivot (see
figure). To bleach laundry without carrying out a full wash
cycle, pour the bleach into the extra compartment 3, select the
“Rinse” cycle and activate the “Super Wash” option .
! It cannot be used in conjunction with , , , , ,
, , .
Extra rinse
By selecting this option, the efficiency of the rinse is increased
and optimal residual detergent removal is guaranteed. It is
particularly useful for skin which is sensitive to detergents. We
recommend this option is used with a full load of washing, or
when a large amount of detergent is required.
! It cannot be used in conjunction with , , , , .
Easy Iron
By selecting this option, the wash and spin cycles will be
modified in order to reduce the formation of creases.
At the end of the cycle the washing machine drum will
rotate slowly; the “Easy Iron” and START/PAUSE indicator
lights will flash. To end the cycle press the START/PAUSE
button or the “Easy Iron” button.
! It cannot be used in conjunction with , , , , , .
Prewash
If this function is selected, the pre-wash cycle will run; this is
useful for removing stubborn stains.
N.B.: put the detergent in the relevant compartment.
! It cannot be used in conjunction with , , , , ,
, , , , (60°), , .
3
1
2
Table of wash cycles
Icon
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergent and additives
Max. load (kg)
Residual
dampness % Energy con-
sumption
kWh
Total water lt
Cycle dura-
tion
Pr
ewash W
ash
Bleach Fabric
softener
Synthetics Resistant 60° 800     3,5 49 0,87 42 90’
Synthetics Resistant (4) 40° 800     3,5 49 0,56 42 85’
Whites 60° 1200   -  4 - - - 190’
Coloureds 40° 1200     4 53 0,90 73 95’
Darks 30° 800 -  -  4 - - - 80’
Shirts 40° 600 -    2 - - - 85’
Quilted Jacket: to wash clothes padded with goose down (such as
puffa jackets) or cushions.
30° 1000 -  -  1,5 - - - 130’
Bed&Bath for bedlinen and towels. 60° 1200     7 - - - 135’
Rinse - 1200 - -   7 - - - 49’
Spin and Pump out - 1200 - - - - 7 - - - 16’
Anti Allergy 60° 1200 -  -  4 - - - 200’
Ultradelicates 30° 0 -  -  1 - - - 75’
Wool: for wool, cashmere, etc. 40° 800 -  -  1,5 - - - 80’
Mix 30': to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800 -  -  3 71 0,19 39 30’
Cotton Standard 60°C (1): heavily soiled whites and resistant colours.
60°
(Max. 90°)
1200  (3)    7 53 1,00 52,5 185’
Cotton Standard 40°C (2): lightly soiled whites and delicate colours. 40° 1200 -    7 53 1,09 92 170’
Cotton Standard 20°C: lightly soiled whites and delicate colours. 20° 1200 -    7 - - - 175’
Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value
will then be shown on the display.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for
garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for
garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
3) At 60 °C the “Prewash” function cannot be selected.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.
4) Long wash cycle for synthetics: set wash cycle with a temperature of 40°C.