Blomberg WNF 6180 WEN - Manuale (Pagina 11)

11 EN
Auxiliary function selection
Select the desired auxiliary functions before starting
the programme. Furthermore, you can also select
or cancel auxiliary functions that are suitable to
the running programme without pressing the Start
/ Pause / Cancel button when the machine is
operating. For this, the machine must be in a step
before the auxiliary function you are going to select
or cancel.
If the auxiliary function cannot be selected or
canceled, light of the relevant auxiliary function will
blink 3 times to warn the user.
C Some functions cannot be selected together. If a
second auxiliary function conflicting with the first
one is selected before starting the machine, the
function selected first will be canceled and the
second auxiliary function selection will remain
active.
C An auxiliary function that is not compatible
with the programme cannot be selected. (See
"Programme and consumption table")
C Auxiliary Function buttons may vary according to
the model of the machine.
• Prewash
A Prewash is only worthwhile for heavily soiled
laundry. Not using the Prewash will save energy,
water, detergent and time.
C As their meshed texture causes excessive
foaming, wash the veils/tulle by putting little
amount of detergent into the main wash
compartment. Do not put detergent in the
prewash compartment.
• Rinse Plus
This function enables the machine to make another
rinsing in addition to the one already made after the
main wash. Thus, the risk for sensitive skins (babies,
allergic skins, etc.) to be effected by the minimal
detergent remnants on the laundry can be reduced.
• Rinse Hold
If you are not going to unload your clothes
immediately after the programme completes, you
can use rinse hold function to keep your laundry
in the final rinsing water in order to prevent them
from getting wrinkled when there is no water in the
machine.
In models equipped with Spin Speed Adjustment
button, select the Spin Speed and press Start /
Pause / Cancel button if you want to spin the laundry
held in water.
In models not equipped with Spin Speed Adjustment
button, select Spin+Pump programme if you want to
spin your laundry held in water.
C In these models, you need to stop the machine
by pressing Start / Pause / Cancel button
before switching to spin step and after pump
step is completed and the water in the machine
is drained. Thus, water inside the machine is
drained and your laundry is not spun.
• No Heat
Use this function if you want to wash your laundry in
cold water.
• No Spin
Use this function if you do not want your clothes be
spun at the end of the programme.
• Spin speed reduction
This function allows spinning of laundry at a speed
lower than the maximum spin speed of the machine.
When Spin Reduction button is pressed, spin speed
will be limited to the minimum speed specified on the
control panel.
Starting the programme
Press Start / Pause / Cancel button to start the
programme. Start / Pause / Cancel button lights up
to indicate that the programme has started. Loading
door is locked and Loading Door light turns off.
Child Lock
Use Child Lock function to prevent children from
tampering with the machine. Thus you can avoid any
changes in a running programme.
C You can switch on and off the machine with On
/ Off button when the Child Lock is active. When
you switch on the machine again, programme
will resume from where it has stopped with the
child lock enabled.
To activate the Child Lock:
Press and hold 1 st and 2 nd Auxiliary Function
buttons for 3 seconds simultaneously after washing
programme has started. The 1 st Auxiliary Function
light flashes continuously.
To deactivate the Child Lock:
Child lock must be deactivated to start a new
programme after the programme has finished or to
interrupt a running program.
Press and hold 1 st and 2 nd Auxiliary Function buttons
for 3 seconds simultaneously to disable child lock.
Progress of programme
Progress of a running programme can be followed
from the Programme Follow-up indicator. At the
beginning of every programme step, the relevant
indicator light will turn on and light of the completed
step will turn off.
To change the auxiliary function, speed and
temperature settings while a program is running, you
need to switch the machine to Pause mode. Press
Start / Pause / Cancel button to switch the machine
into Pause mode. In this case, Start / Pause / Cancel
light flashes.
C If the machine does not pass to the spinning
step, Rinse Hold function might be active or the
automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the machine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
when the water level is unsuitable.
When machine is switched to Pause mode, it checks
the level of the water inside. If the level is suitable,
Loading Door light illuminates steadily within 1-2
minutes and the loading door can be opened.
If the Loading Door light is not on, Loading Door
cannot be opened. If you are obliged to open the
Loading Door while the Loading Door light is off, you
must cancel the current programme; see "Canceling
the programme".