Mp2000 air conditioners – Dell MP2000 Manuale d'uso

Pagina 46

Advertising
background image

RC GROUP - 149_ItEn.0102

46

MP2000 AIR CONDITIONERS

Sistema di controllo a microprocessore per condizionatori d'aria •

Air conditioners microprocessor control system

ed è necessario verificare la configurazione hardware.

unità 1

codici indirizzamento

1-2-3

unità 2

codici indirizzamento

4-5-6

unità 3

codici indirizzamento

7-8-9

unità 4

codici indirizzamento

10-11-12

terminale remoto "T" codici indirizzamento

15

L'eventuale posizione diversa da quanto indicato comporta
un malfunzionamento della rete e deve essere ripristinata.
Per una rete LAN non in configurazione massima (numero
di unità inferiore a 4) il Terminale Remoto "T" assume
sempre lo stesso codice di indirizzamento (15).

CONFIGURAZIONE SOFTWARE MANUALE
Per una più semplice impostazione dei parametri della rete
LAN è importante chiarire alcuni concetti sulla struttura del
sistema di controllo a microprocessore MP2000:
- Il Terminale è privo di memoria ed è esclusivamente

un'interfaccia tra l'utente e le schede Board dell'unità.

- La scheda Board "A" è il cuore del sistema e gestisce

l'unità sulla quale è installata.

- La scheda Board "B" è di supporto alla scheda Board "A"

con funzioni descritte nel manuale.

La rete LAN del sistema di controllo a microprocessore
MP2000 è estremamente versatile e consente molteplici
possibilità di configurazione software:
- per ogni unità è possibile configurare le schede Board dal

terminale a bordo macchina (operazione consigliata).

- è possibile configurare tutte le schede Board presenti

nella rete da qualsiasi terminale presente nella rete.

- è possibile configurare tutte le schede Board presenti

nella rete dal terminale remoto.

Inoltre ogni scheda Board può comunicare con massimo 3
terminali.
Ad esempio la scheda Board "A" dell'Unità 1 può comuni-
care con il proprio terminale a bordo macchina, con il
terminale remoto e con il terminale dell'Unità 2.

CONFIGURAZIONE
Premere contemporaneamente i tasti HOME-SET-PRG per
6 secondi e comparirà la prima maschera di configurazione:

Dove:
Terminal Adr: --

indica il codice di indirizzamento del
terminale su cui si agisce.
Questo codice di indirizzamento è fis-
so ed è definito dall'impostazione
hardware dei dip-switch del terminale.

I / O Board Adr: -- con i tasti FRECCIA si seleziona il

codice di indirizzamento della scheda
Board che si vuole configurare.
Premendo ENTER si conferma il dato
impostato.

Terminata l'impostazione del codice di indirizzamento del-
la scheda Board sul display compare

hardware configuration.

unit 1

address code

1-2-3

unit 2

address code

4-5-6

unit 3

address code

7-8-9

unit 4

address code

10-11-12

"T" remote terminal

address code

15

Wrong or different positions cause a network malfunction.
For a LAN network not in maximum configuration (number
of units lower than 4) the "T" Remote Terminal has always
the same address code (15).

MANUAL SOFTWARE CONFIGURATION
For a simple set up of the LAN network, it is necessary to
clarify same concepts of the MP2000 microprocessor con-
trol system:
- Terminal is lack of memory. It is simply an interface from

Board "A" and operator.

- Board "A" is the system core and is managing the unit.
- Board "B" is the supporting card for Board "A" with

functions described in the manual.

The MP2000 microprocessor control system LAN network
is extremely versatile and allows various software configu-
rations:
- Boards configuration, for each unit, directly from the unit

Terminal (suggested operation).

- Boards configuration of the entire network from any

Terminal.

- Boards configuration of the entire network from the

Remote Terminal.

Moreover each Board can communicate with max 3 Termi-
nals.
For example Board "A" of Unit 1 can communicate with its
own Terminal, with Remote Terminal and with Unit 2
Terminal.

CONFIGURATION
Press simultaneously HOME-SET-PRG keys for 6 sec-
onds and the first configuration mask will appear:

Where:
Terminal Adr: --

shows the address code of the Termi-
nal where you operate.
This address code is fixed. It is set by
terminal dip-switches of the hardware
configuration.

I / O Board Adr:--

by press ARROW keys it is possible to
select the address code of the Board
to be configurated.
Press ENTER to data confirmation.

At the end of the Board address code setting, on display will
appear

Terminal

Adr

:

1

I / O Board

Adr

:

--

Advertising