Mp2000 air conditioners – Dell MP2000 Manuale d'uso

Pagina 179

Advertising
background image

179

RC GROUP - 149_ItEn.0102

MP2000 AIR CONDITIONERS

Sistema di controllo a microprocessore per condizionatori d'aria •

Air conditioners microprocessor control system

HC1 (Heating/Cooling uscita 1): Modo di funziona-

mento uscita 1.
H = Caldo - C = Freddo

HC2 (Heating/Cooling uscita 2): Modo di funziona-

mento uscita 2. Analogo a HC1

rP1 (Relè protection 1). Stabilisce la posizione del relè

1 in caso di sonda guasta.
ro =relè aperto - rc =relè chiuso.

rP2 (Relè protection 2). Stabilisce la posizione del relè

2 in caso di sonda guasta. Analogo a rP1

LF1 (LED Function 1). Indica se il LED 1 deve essere

acceso o spento in corrispondenza all'uscita 1 attiva.
di =diretta = LED acceso per uscita attiva
in =inversa = LED spento per uscita attiva

LF2 (LED Function 2). Indica se il LED 2 deve essere

acceso o spento in corrispondenza all'uscita 2 attiva.
Analogo a LF1.

dP (decimal point). Permette di avere la visualizzazione

con o senza punto decimale.
oF =senza punto decimale - on = con punto decimale

hdd (half digit display). Permette di selezionare sulla

cifra più a destra del display la visualizzazione normale
(hdd =n) o delle sole cifre 0 e 5 (y) - risoluzione di 0,5

°

C.

tAb (tAbella parametri). Indice di configurazione para-

metri settati in fabbrica; non modificabili dall'utente.

Fig.114

SEGNALAZIONE ERRORE
Il controllo visualizza due tipi di errore:

- - - nel caso di sonda in corto circuito.
EEE nel caso di sonda interrotta, non collegata e valori di

temperatura fuori range.

L'uscita su relè è libera da tensione ed indipendente.
Non superare la corrente massima (6A/250 Vac/AC1).
Con carichi superiori usare un contattore di adatta potenza.

DATI TECNICI
Alimentazione

24Vac/dc

±

15% - 50/60Hz - 3VA

Portata contatto relè

6A - 250Vac - AC1

Potere di commutazione 1000VA (Vac) - 50W (Vdc)

HC1 (Heating/Cooling output 1): Relay switch function

output 1.
H = Heating - C = Cooling

HC2 (Heating/Cooling output 2): Relay switch function

output 2. Same as HC1

rP1 (Relay protection 1). Determines the status of the

relay 1 in case of sensor defect.
ro =relay open - rc =relay closed

rP2 (Relay protection 2). Determines the status of the

relay 2 in case of sensor defect. Same as rP1

LF1 (LED Function 1). Determines whether the status

light is ON or OFF in relation to output 1.
di =direct= light on when output 1 is energized
in =reverse= light off when output 1 is energized

LF2 (LED Function 2). Determines whether the status

light is ON or OFF in relation to output 2.
Same as LF1.

dP (decimal point). Choose whether the resolution is

required with or without decimal point.
oF =Without decimal point - on = With decimal point

hdd (half digit display). The right-most digit can be set

to read-out in 0 or 5 only, or in all 10 digits.

tAb (tAble of parameters). This shows the configura-

tion of the parameters as set in the factory; can not be
modified.

ERROR SIGNALLING
The device display two type of error:
- - -

in case of sensor in short-circuit.

EEE in case of sensor break, sensor absence or tempera-

ture values out of range.

The relay output contact is voltage free and independent.
Do not exceed the resistive rating of 6A/250Vac/AC1.
For larger loads, please use an external contactor or relay.

TECHNICAL DATA
Feeding

24Vac/dc

±

15% - 50/60Hz - 3VA

Relay resistive rating

6A - 250Vac - AC1

Commutation cap.

1000VA (Vac) - 50W (Vdc)

OFF

OFF

ON

ON

I

II

Set point 2

Set point 1

d1

d2

(

°

C)

Advertising