Mp2000 air conditioners, Possibili configurazioni del siste- ma mp2000, Possible configurations of the mp2000 system – Dell MP2000 Manuale d'uso

Pagina 17

Advertising
background image

17

RC GROUP - 149_ItEn.0102

POSSIBILI CONFIGURAZIONI DEL SISTE-
MA MP2000

CONFIGURAZIONE CON BOARD "A" E TERMINALE A
BORDO MACCHINA
Questo tipo di configurazione è adatta per le seguenti unità:
- Condizionatori alimentati con acqua refrigerata
- Condizionatori equipaggiati con un compressore
- Condizionatori equipaggiati con due compressori su

unico circuito frigorifero.

Il sistema MP2000 comprende la scheda BOARD "A" con
la scheda "ADDR" ed il TERMINALE.
Con questa configurazione il sistema controlla totalmente
l'unità e visualizza sul display tutti gli stati di funzionamento
e gli eventuali allarmi intervenuti.
Per il corretto funzionamento del sistema è necessario
impostare i codici di indirizzamento, indicati tra parentesi
nella figura, sui dip-switch di ogni scheda:
- BOARD "A" codice "2"
- TERMINALE codice "1"
La remotizzazione degli allarmi è possibile solo tramite due
relè di Allarme Generale programmabili con contatto pulito.

A richiesta:
- Porta seriale "RS485"
- Scheda "ADDR+CK"
- Scheda "Umidificatore"

Fig. 12

CONFIGURAZIONE CON BOARD "A" E TERMINALE A
BORDO MACCHINA E/O REMOTO "T"
Questa configurazione presenta le stesse caratteristiche
della precedente ma consente la gestione dell'unità anche
dal TERMINALE REMOTO "T".
Per il corretto funzionamento del sistema è necessario
impostare i codici di indirizzamento, indicati tra parentesi
nella figura, sui dip-switch di ogni scheda:
- BOARD "A" codice "2"
- TERMINALE codice "1"
- TERMINALE REMOTO "T" codice "15"
La remotizzazione degli allarmi è possibile solo tramite due
relè di Allarme Generale programmabili con contatto pulito.
La scheda "T" del condizionatore è fornita non installata in
quanto, in caso di rete LAN, deve essere posizionata
sull'unità più vicina al TERMINALE REMOTO "T".
Il TERMINALE REMOTO "T" e la seconda scheda "T" sono

POSSIBLE CONFIGURATIONS OF THE
MP2000 SYSTEM

CONFIGURATION WITH BOARD "A" AND TERMINAL
ON UNIT
This configuration is suitable for the following units:
- Air conditioners with chilled water feeding,
- Air conditioners equipped with one compressor,
- Air conditioners equipped with two compressors working

on a single gas circuit.

The the MP2000 microprocessor control system includes
BOARD "A" with "ADDR" board and TERMINAL.
In this configuration, the system controls the unit showing
on the display all the unit working status and the eventual
intervened alarms.
For a correct system operation it is necessary to set the
address code, between brackets in the picture, on dip-
switch of each board.
- BOARD "A" code "2"
- TERMINAL code "1"
The alarms remotization is possible only through two
General Alarm relays with voltage free contact.

On request:
- Serial port "RS485"
- Board "ADDR+CK"
- Board "Humidifier"

CONFIGURATION WITH BOARD "A" AND TERMINAL
ON UNIT AND/OR "T" REMOTE
This configuration has the same characteristics of the
previous one, but allows the unit management also from
the "T" REMOTE TERMINAL.
For a correct system operation it is necessary to set the
address code, between brackets in the picture, on dip-
switch of each board.
- BOARD "A" code "2"
- TERMINAL code "1"
- "T" REMOTE TERMINAL code "15"
The alarms remotization is possible only through two
General Alarm relays with voltage free contact.
The air conditioner "T" board is supplied not installed
because, in case of LAN network, it has to be positioned on
the unit closest to the "T" REMOTE TERMINAL.
The "T" REMOTE TERMINAL and the second "T" board

MP2000 AIR CONDITIONERS

Sistema di controllo a microprocessore per condizionatori d'aria •

Air conditioners microprocessor control system

RS

485

CK

ADDR

Umidif.

Humidif.

TERMINAL

CONDIZIONATORE

AIR CONDITIONER

BOARD

A

ADDR

TERMINAL

CONDIZIONATORE

AIR CONDITIONER

BOARD

A

STANDARD

OPTIONAL

(1)

(2)

(1)

(2)

Advertising