Mp2000 air conditioners – Dell MP2000 Manuale d'uso
Pagina 132
RC GROUP - 149_ItEn.0102
132
MP2000 AIR CONDITIONERS
Sistema di controllo a microprocessore per condizionatori d'aria •
Air conditioners microprocessor control system
AL27
Non utilizzato.
AL28 - Manutenzione
L’allarme interviene quando le ore di funzionamento di uno
o più componenti della macchina supera il valore impostato
nel relativo parametro "Threshold hour ……..".
Se il parametro "Threshold hour" viene impostato a "0",
l'allarme del relativo componente viene inibito.
Sul terminale viene visualizzata la seguente segnalazione
(premendo il tasto Alarm):
Y Indica che il relativo componente necessita di manu-
tenzione.
N Indica che il relativo componente non necessita di
manutenzione.
— Indica che il relativo componente non è presente in
configurazione.
Legenda Componenti:
Simbolo
Componente
Parametro
(Service Password)
Threshold hour...
Fan
Ventilatore principale
Main Fan
C1
Compressore 1
Compr. 1
C2
Compressore 2
Compr. 2
H1
Resistenza 1
Heater 1
H2
Resistenza 2
Heater 2
H
Umidificatore
Dehum\Hum
D
Deumidificazione
Dehum\Hum
L'allarme viene solo segnalato.
Remotizzazione allarme con contatto pulito su scheda
Board B uscita C10.
Ripristino automatico, dopo aver azzerato le ore di funzio-
namento del componente interessato.
AL29 - Differenziale Olio Compressore 1
Scheda Board B ingresso ID 4.
L’allarme interviene quando il compressore 1 è acceso, e
si apre l’ingresso ID4, trascorso il tempo impostato nel
parametro "Oil differential alarm delay time".
Il conteggio viene azzerato se l’ingresso si richiude e/o il
compressore si ferma.
Viene fermato il Compressore 1.
Remotizzazione allarme con contatto pulito su scheda
Board B uscita C5.
Ripristino Manuale.
AL30 - Differenziale Olio Compressore 2
Scheda Board B ingresso ID 5.
L’allarme interviene quando il compressore 2 è acceso, e
si apre l’ingresso ID5, trascorso il tempo impostato nel
parametro "Oil differential alarm delay time".
Il conteggio viene azzerato se l’ingresso si richiude e/o il
compressore si ferma.
Viene fermato il Compressore 2.
Remotizzazione allarme con contatto pulito su scheda
Board B uscita C6.
Ripristino Manuale.
AL 28
Maintenance Alarm
Fan:Y
C1:N
H1:N
H:--
C2:--
H2:N
D:--
AL 27
Not used
Al 28 – Maintenance
The alarm is activated when the running hours of one or
more components exceeds the value preset in the relative
"Threshold hour ..." parameter.
If the parameter "Threshold hour" is setted to "0", the alarm
of the relevant component is inhibited. The following signal-
ling is displayed on the terminal (press the Alarm key):
Y indicates that the relative components needs mainte-
nance.
N indicates that the relative component needs not any
maintenance.
–
indicates that the relative probe is absent or under
configuration
Legends:
Symbol
Component
Parameter
(Service Password)
Threshold hour ...
Fan
Main fan
Main fan
C1
Compressor 1
Compr. 1
C2
Compressor 2
Compr. 2
H1
Heater 1
Heater 1
H2
Heater 2
Heater 2
H
Humidifier
Dehum\Hum
D
Dehumidification
Dehum\Hum
The alarm is only signalled.
Alarm remotization with voltage free contact on Board B,
output C10.
Automatic reset, after resetting the running hours of the
component.
AL 29 – Compressor 1 Oil Differential
Board B, input ID 4.
The alarm is activated when compressor 1 is ON and input
ID 4 is opened, after the time preset in the "Oil differential
alarm delay time" parameter.
The count is reset in the input is re-closed and/or the
compressor is stopped.
Compressor 1 is stopped.
Alarm remotization with voltage free contact on Board B,
output C5.
Manual reset.
AL 30 – Compressor 2 Oil Differential
Board B, input ID 5.
The alarm is activated when compressor 2 is ON and input
ID 5 is opened, after the time preset in the "Oil differential
alarm delay time" parameter.
The count is reset if the input is re-closed and/or the
compressor is stopped.
Compressor 2 is stopped.
Alarm remotization with voltage free contact on Board B,
output C6.
Manual reset.